Managed Residential · A/C · Electrical
24 A/C Units, One Building: A Full-Building HVAC Replacement for a Managed Apartment Community
We replaced every A/C unit in a managed Jacksonville apartment building: 24 systems removed, installed, tested, and documented, plus duct remediation and an electrical report.

The challenge
A property management company needed to replace the air conditioning in every unit of one of its apartment buildings. A job like this is different from a single-home replacement. There are 24 systems, the residents still live there, and the property manager has to answer to owners, tenants, and a budget.
The manager needed a contractor who could:
- Price the job competitively across all 24 systems
- Run the work with as little disruption to residents as possible
- Do every install to the same standard, from the first unit to the last
- Leave the property with a clear record of what was done and what to watch
Why they chose Copper & Co.
The client gave three reasons for choosing us: price, service, and the quality of our field work.
At this scale, price matters. Our bid was competitive. But a low number alone doesn’t win a building. The client also wanted a team that would communicate clearly, show up when scheduled, and do clean, consistent work in every apartment. That combination is what we deliver as an HVAC and electrical contractor.
Our scope of work
1. Refrigerant pump-down and recovery
Before any equipment came out, our technicians pumped down and recovered the refrigerant from each existing system following EPA refrigerant-handling requirements. Refrigerant is never vented. Recovering it properly protects the environment, keeps the property compliant, and makes the removal phase safer for everyone on site.
2. Demolition, removal, and disposal
We disconnected, removed, and hauled away all 24 old systems. Disposal was part of our scope, so the property manager had nothing left to coordinate: no old units on the property and no separate hauling vendor. Work areas were cleaned as we went.
3. Installation of 24 new systems
New equipment was sized to match each apartment’s existing capacity:
- 21 two-ton systems for the building’s standard floor plans
- 2 two-and-a-half-ton systems for the larger units
- 1 one-and-a-half-ton system for the smallest unit
For this project, the client chose to connect the new systems to the building’s existing electrical service and ductwork. That kept costs down and shortened the schedule, and we confirmed every connection before commissioning. (On other projects we can upgrade electrical and ductwork in the same job, since we do both trades in-house.)
4. Startup and testing
We commissioned and tested each system individually before calling it complete, including a pressure check on every system to confirm it was charged and running within the manufacturer’s specifications. Every one of the 24 apartments got the same startup process, so the property manager could be sure each install met our standard and none were rushed through.
5. Duct mold and odor remediation
Because the existing ductwork stayed in place, we treated it with a mold and odor remediation fog. Old ductwork in Florida’s humid climate often builds up musty smells and microbial growth. If you hook a new system to dirty ducts, residents still notice the old smell. Treating the ducts means tenants get both new equipment and better-smelling air from day one.
6. Electrical site report at closeout
Because Copper & Co. is both an electrical and HVAC contractor, our technicians look at more than the A/C. During the project, our team noted electrical conditions on site that may need attention in the near future. At closeout we gave the client a written electrical report documenting what we found.
The property manager now has a clear, prioritized view of what to watch, what to budget for, and what to address before it becomes an emergency call. Most HVAC-only contractors don’t offer this. With us, it comes standard because we know both trades.
The result
- 24 new A/C systems installed, tested, and running across a full building
- 48.5 tons of cooling capacity replaced
- Old equipment and refrigerant handled and disposed of properly
- Ductwork treated for mold and odor
- A written electrical report so the property can plan ahead
The property manager handed the whole building to one contractor and got a documented, consistent result back.
Why this matters for property managers
Replacing HVAC across a building is as much a coordination job as a technical one. Working with one contractor that covers both HVAC and electrical means:
- One point of contact instead of separate HVAC and electrical vendors
- Problems caught early. Our techs know what a failing disconnect or overloaded circuit looks like.
- Consistent work in every unit, documented at closeout
- Flexible scope. Reuse existing infrastructure where it makes sense, or upgrade it where it doesn’t.
Whether it’s one building or an entire community, we can scale to the job.